|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
Vacuum Mixing & Casting System
with
PLC Based Controller
complete with vacuum regulation and Motor Start/stop Contactor
We will design and build to your process system requirements
The Degassing/Mixing Chamber has a clear Acrylic lid with four latches to maintain the seal while under pressure. The lid has a manual rotary feedthru and handle attached. To the shaft of this feedthru is attached a mixing impeller, sized appropriately for the encapsulant container being used. The chamber accommodates plastic beakers of various sizes. The beakers are held down using three threaded rods with wing nuts and a cover plate. There are two sets of holes, rods and cover plate used for small or large containers This Controller is designed to be a part of our rugged bench top vacuum chambers in production or testing. Some of our customers find this to be a practical solution for using a vacuum chamber in a controlled process to dry products, and degas of parts, liquids, plastics, resins, and epoxies. This regulator and cycle controller allows the whole vacuum operation, from start to finish, to be controlled, yielding a more consistaint product process. After set-up, the chamber and vacuum system can automatically turn on the vacuum, watch for the preset vacuum level, then control the hold time at that vacuum level, then break the vacuum to allow the operator to remove and replace product. All this can happen without the operator watching. Your product becomes more consistant and your process more reliable. Custom features are always an option. We can design in PLCs or computer interfaces with control software and temperature control elements. Call, us lets talk about your process requirements. It is constructed of standard industrial parts. Enclosures are for indoor use to provide protection from dust, dirt, and splashing and spraying oil/coolant. Also rated NEMA 13 for protection from oil/coolant dripping. Made of 14-ga. steel (unless noted) with gray powder-coated finish. Enclosures are also known as JIC (Joint Industrial Council) boxes. Covers have a neoprene gasket and secure with a screw clamp on one side. Enclosures are UL listed and CSA certified.
If you have any questions, custom configurations, or need pricing, please e-mail us at
abbess@abbess.com
|
Standard Features
|
|
|---|---|
| Dimensions: | Standard -
Degassing/Mixing Chamber The upper Degassing/Mixing Chamber is a cylindrical chamber (Dimensions: 15” dia x 24” high) in which the one or two-part encapsulating compound is placed. The Vacuum chamber is constructed of heavy Aluminum with a cast Acrylic lid. A customer replaceable O-ring seal is employed to withstand repeated closings. Four draw latches are used to secure the lid to the chamber. The chamber is used to degas and mix the encapsulant under vacuum to eliminate air bubbles. Once mixed, the chamber is pressurized to facili tate flow of the high viscosity encapsulant through the Liquid Feedthru tubes and into the molds in the lower Casting Chamber. The Degassing/Mixing Chamber has a clear Acrylic lid with four latches to maintain the seal while under pressure. The lid has a manual rotary feedthru and handle attached. To the shaft of this feedthru is attached a mixing impeller, sized appropriately for the encapsulant container being used. The chamber accommodates plastic beakers of various sizes. The beakers are held down using three threaded rods with wing nuts and a cover plate Casting Chamber The lower Casting Chamber is a cube-shape chamber (Dimensions: 24” high x 24” wide x 24” deep) in which the molds to be filled under vacuum are placed. The Vacuum chamber is constructed of heavy Stainless Steel 304 with a cast Acrylic door. A customer replaceable O-ring seal is employed to withstand repeated closings. Two draw latches on the right side are used to close the front-hinged door. All chambers are vacuum tested to 29.92 inches of Hg or better (10-7 torr if required) and should maintain this for its life dependent on seal condition and customer use. The chamber is equipped with two removable shelves and associated brackets. The Liquid Feedthru tubes extend into the chamber to be positioned over the molds by the customer. Vacuum Pump Welch Duo-Seal 1374 – See included documentation for maintenance and operating instructions. Mobile Cart The mobile cart includes casters for mobility. Also included are screw-type leveling feet. These feet should be extended down during operation to stabilize the system. |
|
Included Features:
|
Electronic vacuum cycle digital timer (.05 to 999 seconds- customer set)
Adjustable vacuum switch (for sensing the vauum level for the start point of the timer) Vacuum Regulator (for controlling the vacuum level) Long life LED indicators (indicate system status) Vacuum Gauge on top of regulator (indicates vacuum system operation/pump function) |
| Optional Features: | Selectable Venting Rates |
| Vacuum Pump power control (Motor Start/stop Contactor)
Turns vacuum pump on at start and off at the end of cycle. |
|
| Custom - extra cycles or connections | |
| Digital Torr Control with 2 setpoints | |
We Mix in the vacuum to prevent air bubbles
We build to your process system requirements
Back to top of Abbess Main Home Page
 |
 |
|||
 |
||||
|
If you have any questions, need custom configurations, or a quotation,
please e-mail us at
|
||
